68 lines
2.0 KiB
Plaintext
68 lines
2.0 KiB
Plaintext
|
[LOAD_CFG]
|
||
|
|
#jlink or uart
|
||
|
|
interface = uart
|
||
|
|
device = COM1
|
||
|
|
speed_uart_boot = 500000
|
||
|
|
speed_uart_load = 500000
|
||
|
|
#cklink usb vid|pid
|
||
|
|
cklink_vidpid = 42bf|b210
|
||
|
|
cklink_type = CKLink_Lite_Vendor-rog
|
||
|
|
#eg: rv_dbg_plus, ft2232hl, ft2232d
|
||
|
|
openocd_config = rv_dbg_plus
|
||
|
|
auto_burn = false
|
||
|
|
speed_jlink = 2000
|
||
|
|
#0:without load, 1:eflash_loader load
|
||
|
|
load_function = 1
|
||
|
|
do_reset = true
|
||
|
|
#reset retry+hold time
|
||
|
|
reset_hold_time = 50
|
||
|
|
shake_hand_delay = 100
|
||
|
|
reset_revert = false
|
||
|
|
cutoff_time = 50
|
||
|
|
shake_hand_retry = 3
|
||
|
|
flash_burn_retry = 1
|
||
|
|
checksum_err_retry = 3
|
||
|
|
#1: 32M, 2: RC32M
|
||
|
|
#xtal_type = 2
|
||
|
|
erase_time_out = 15000
|
||
|
|
#chiptype=702
|
||
|
|
eflash_loader_file=chips/bl702/eflash_loader/eflash_loader_32m.bin
|
||
|
|
check_mac = true
|
||
|
|
#0:no erase,1:programmed section erase,2:chip erase
|
||
|
|
erase = 1
|
||
|
|
# switch eflash_loader command log save
|
||
|
|
local_log = false
|
||
|
|
#0:verify by calculating SHA256(xip), >0:read back verify and verify by calculating SHA256(sbus)
|
||
|
|
verify = 0
|
||
|
|
tx_size = 2056
|
||
|
|
cpu_reset_after_load = false
|
||
|
|
#skip mode set first para is skip addr, second para is skip len
|
||
|
|
skip_mode = 0x0, 0x0
|
||
|
|
boot2_isp_mode = 0
|
||
|
|
isp_mode_speed = 2000000
|
||
|
|
isp_shakehand_timeout = 0
|
||
|
|
|
||
|
|
[FLASH_CFG]
|
||
|
|
flash_id = c84015
|
||
|
|
#flash clock 0:72M, 1:36M, 2:24M, 3:18M
|
||
|
|
flash_clock_cfg = 2
|
||
|
|
#0:NIO, 1:DO, 2:QO, 3:DIO, 4:QIO
|
||
|
|
flash_io_mode = 1
|
||
|
|
#flash_pin value:
|
||
|
|
#bit 2-3 = flash_cfg: 0: external gpio 23-28, 1: internal 512K, 2: internal 1M, 3: external gpio 17-22
|
||
|
|
#bit 0-1 = swap_cfg: 0: do not swap, 1: swap cs&io2, 2: swap io0&io3, 3: swap cs&io2 io0&io3 both
|
||
|
|
flash_pin = ""
|
||
|
|
#empty for auto, otherwise specified para file path: eg: chips/bl702/efuse_bootheader/flash_para.bin
|
||
|
|
flash_para = chips/bl702/efuse_bootheader/flash_para.bin
|
||
|
|
decompress_write = false
|
||
|
|
file = chips/bl702/img_create/bootinfo_boot2.bin chips/bl702/img_create/img_boot2.bin chips/bl702/partition/partition.bin chips/bl702/partition/partition.bin
|
||
|
|
address = 00000000 00002000 e000 f000
|
||
|
|
|
||
|
|
[EFUSE_CFG]
|
||
|
|
burn_en = true
|
||
|
|
factory_mode = false
|
||
|
|
security_write = false
|
||
|
|
security_save = true
|
||
|
|
file = ../../../Tools/img_tools/efuse_bootheader/efusedata.bin
|
||
|
|
maskfile = ../../../Tools/img_tools/efuse_bootheader/efusedata_mask.bin
|